E-TEC Electrical Contractors
East Point, GA




Journeyman Electrician

Work Type




Minimum Experience

6 Years



Work will consist of installation, alterations, additions, and/or repairs of electrical systems, conductors, and associated materials and equipment within the electrical construction industry.



Performs all electrical tasks with minimal general supervision. This employee may be part of a crew or the lead person directing this crew. Should have the ability to direct less experienced apprentices and helpers.

1. Supervise and work with the crew

2. Install all work

3. Troubleshoot motors, controls, circuits, and equipment

4. Efficient in layout and blueprints

5. Rigging and set-up for all operations

6. Basic theory knowledge

7. Possess skills of lower E-Rating Job Title (E-5, E4, E-3, E-2, E-1)



Licenses: Current Driver’s License and have own transportation, (most job sites are not

always served by public transportation)

Electrical: Current Journeyman

Education: High School Graduate, holder of G.E.D., or equivalent training

Experience: Has 5 years or more of previous electrical experience


1. Job requires working in all elements, depending on job location, time of year, heat, cold, rain, and snow.

2. Must be able to utilize construction site sanitary facilities (Porta-Johns).

3. Job requires the employee to have required personal tools with them at all times (waist tool belt as worn weighs approximately 30 lbs.).

4. Work from all type ladders (step ladders up to 14′, “A” frame ladders and all size extension ladders and carry and relocate up to 12′ step ladder by one’s self.

5. Employee’s personal weight and personal tools cannot exceed the weight limit of ladder (Class 1 – 250 lbs., Class IA – 300 lbs.).

6. Perform work at various heights, up to 90′ from ladders, scaffolds, aerial lifts, catwalks, or other safe work areas.

7. Work in restricted areas (switchgear room, manholes, utility tunnels, crawl spaces, and attics).

8. Wear personal protective equipment (hard hat, safety glasses at all times), respirator when required.

9. Repetitive use of arms, hands, and fingers.

10. Able to work 8 hours per day, 40 hours per week, and overtime as required and night shifts.



1. Positively identify colors of wires.

2. Comprehends reading and drawing prints and schematics of the same.

3. Bend conduit by hand with hand benders.

4. Must use all power tools, saws, threaders, wire tuggers, hydraulic benders, and knockout punches.

5. Capable of digging trenches, either by use of hand tools or power equipment.

6. Operate equipment, trenchers, backhoe, lift trucks in a safe manner.

7. Practices and comprehends safe work procedures as outlined in the Company Safety Policy Handbook, Haz-Com Policy, and Lockout/Tagout Policy.

8. Operates two (2) handed tools/equipment, cable cutters, hammer drills, compression tools, jackhammers.

9. Operate company trucks with manual and automatic transmission.

10. Read and interprets maps, instructional manuals, directions, blueprints, and written instructions.

11. Operate and work from mechanical personnel lifts (electric or gas-powered).

12. Work energized circuits and equipment with company management approval as outlined in appropriate safety policy.

13. Supervise assigned job site employees to complete the project.



1. Must be able to bend, stoop, squat, crawl, climb, kneel, balance, push, pull, and reach overhead.

2. Lift 51 pounds.

3. Constantly moving on your feet.

4. Climb ladders (all types).

5. Completing overhead work for full day assignments.

6. Must be able to make the transition from the employee parking area or street into construction work areas and to gain access to all levels of the building, even if the only means of access is by O.S.H.A. approved site construction ladder or stairs still under construction but acceptable for use.

7. Possess good vision (normal or corrected).

8. Responsible for securing tools and materials from storage areas to complete their assigned tasks.



All elements inside and outside

Candidate Requirements

Willing to Work from Elevated HeightsWilling to Work in Inclement WeatherHigh School DiplomaGEDDriver's LicenseOwns Power ToolsOwns Hand ToolsCan Drive a Manual TransmissionWilling to Work Overtime


Drawings and Code

Can Read Construction BlueprintsProficient in Electrical TheoryCan Read Electrical ManualsCan Read Wiring Schematics


50 lbs.

Startup & Testing



Motor Control Centers (MCCs)Motors


Metal Conduit Bending and Installation

Non-Technical Skills

Management Experience


Equipment Certifications

Aerial Lift Certification



$21 - $25 / hour